Colt Country | Home of The Almighty Colt
Black Powder Pistols => Pocket Models => Topic started by: ShotgunDave on December 10, 2020, 11:31:33 AM
-
Been wanting one of these for my daughter to shoot. Stumbled onto this on GB a week or so ago, and couldn't pass up the deal. I got it really cheap.
(https://live.staticflickr.com/65535/50703546822_4b8639f91c_z.jpg)
It's a 1969 (XXV) made, EIG import by ASM. It says "Marco" on the left side of the frame. It's in decent shape for it's age, but the brass needs a little love. It's nearly black. So my daughter has asked me to polish it back up.
(https://live.staticflickr.com/65535/50702724438_7d5ee02d82_z.jpg)
Literally 10 minutes after unboxing it, I broke the trigger spring. It wasn't any fault of the guns, I over bent it while fiddling with it, and it snapped off in my hand. So I had to make a new one out of wire, as I'm sure parts for this thing are unobtainium. It's not likely to see a ton of use, so I'm not too worried about it. As long as my daughter has her own pistol, she's happy.
-
Looks even better in big pix, Dave! You scored there, brother!
-
Thanks Capt. I agree.
It has really nice case colors on it, but not that "clear coat" look of newer guns. It looks much better to me.
-
It is definitely an ASM just by looking at the rear shoulders of the trigger guard and the load lever pivot area. It also has the short frame, the short forcing cone, and the shallow V-notch load aperture on the barrel lug from the 1848 Pocket. It has the round trigger guard of the 1849.
The 1849 had a longer frame, longer forcing cone, and a larger beveled load aperture.
Historically, Colt only produced the 1848 for one year, followed by the 1849. As Colt never wasted a part, so the story goes, some late production 1848 pistols had round trigger guards, and some early production 1849 pistols had squareback trigger guards.
It appears that ASM was not picky, either.
Replica Arms ASM 1848 Pocket (XIX/1963) 6" barrel that I used to own. I have looong fingers and it got lost in my hand.
(https://i.ibb.co/TcgkqM6/1848-Pocket-31-Replica-Arms-ASM-001.jpg) (https://ibb.co/dB5rJ4F)
So, in actuality you have an 1848 with a round trigger guard. You scored very well.
You had better polish up that brass real purty for your young lady!
Regards,
Jim
-
Congratulations on a great find.
-
Thanks fellas.
And thank you Jim. You just taught me some stuff!
-
I learn something new nearly every day. Now, retaining that info is a different story. *6'
-
My recently acquireda 1969 built[/img] Armi San Marco Baby dragoon?? Incorrect with round barrel?? Some one had tried to use a Uberti bolt/trigger spring. Needed quite a bit of re-working to work.
Shotgun Dave what spring material did you use
There must have a lot of "hand fitting" by ASM back then, all parts even the wedge have serial #s. The trigger and bolt screws are even slightly different lengths, to accommodate the slight taper of the frame
-
Leave the brass alone! Much nicer than polished
-
My recently acquireda 1969 built[/img] Armi San Marco Baby dragoon?? Incorrect with round barrel?? Some one had tried to use a Uberti bolt/trigger spring. Needed quite a bit of re-working to work.
Shotgun Dave what spring material did you use
There must have a lot of "hand fitting" by ASM back then, all parts even the wedge have serial #s. The trigger and bolt screws are even slightly different lengths, to accommodate the slight taper of the frame
44 Dave, that's a nice pistol! And pretty rare with the Dragoon style barrel. That's a really nice find.
As for the trigger/bolt spring, I just used a nice quality safety pin. The coiled end of the pin makes a nice place for the screw to go through. And the pin is made of nice springy steel. It only took a couple minutes and a couple pair of pliers to make it. Added bonus of doing it this way is, you get a lighter trigger pull.
I'll pop the trigger guard off tomorrow and get a picture for you.